ata2.00: status: { DRDY } ata2.00: cmd 61/08:f0:47:00:00/00:00:00:00:00/40 tag 30 ncq 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata2.00: status: { DRDY } ata2: hard resetting link ata2: SATA link up 3.0 Gbps (SStatus.. 정보
ata2.00: status: { DRDY } ata2.00: cmd 61/08:f0:47:00:00/00:00:00:00:00/40 tag 30 ncq 4096 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata2.00: status: { DRDY } ata2: hard resetting link ata2: SATA link up 3.0 Gbps (SStatus..본문
ata2.00: status: { DRDY }
ata2.00: cmd 61/08:f0:47:00:00/00:00:00:00:00/40 tag 30 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
SCSI device sdb: 1953525168 512-byte hdwr sectors (1000205 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
solve)
First i would check the cable, make sure its the flat ribbon kind no more than a few inches long, sometimes the longer, round kind gives errors because they are out of spec.
There is a sector error there, so check what SMART says:
sudo smartctl -H /dev/sdf
This should give you a quick response as to SMART finding anything bad in the past or now.
Also do:
sudo smartctl -A /dev/sdf
post the values table that it gives you, you should be able to see though if there are a lot of some specific errors.
Probably a good idea to have SMART run an extended selftest on the drive anyway:
sudo smartctl --test=long -C /dev/sdf
This will run the extended selftest, and it will tell you how long it takes. When it is done you can get the results like this:
sudo smartctl --log=selftest /dev/sdf
centos)
smartmontools i386 1:5.36-4.el5 base 294 k
ata2.00: cmd 61/08:f0:47:00:00/00:00:00:00:00/40 tag 30 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata2.00: status: { DRDY }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
SCSI device sdb: 1953525168 512-byte hdwr sectors (1000205 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
solve)
First i would check the cable, make sure its the flat ribbon kind no more than a few inches long, sometimes the longer, round kind gives errors because they are out of spec.
There is a sector error there, so check what SMART says:
sudo smartctl -H /dev/sdf
This should give you a quick response as to SMART finding anything bad in the past or now.
Also do:
sudo smartctl -A /dev/sdf
post the values table that it gives you, you should be able to see though if there are a lot of some specific errors.
Probably a good idea to have SMART run an extended selftest on the drive anyway:
sudo smartctl --test=long -C /dev/sdf
This will run the extended selftest, and it will tell you how long it takes. When it is done you can get the results like this:
sudo smartctl --log=selftest /dev/sdf
centos)
smartmontools i386 1:5.36-4.el5 base 294 k
공감
0
0
댓글 0개